MULTICOMP  HT-225D  Crimp Tool, Ratchet, 30-18AWG D-Sub Contacts

MULTICOMP HT-225D

Image is for illustrative purposes only. Please refer to product description.

Additional images

  • Manufacturer:
  • Newark Part No.: 01P3570
  • Manufacturer Part No HT-225D

Product Overview


The HT-225D from Multicomp is a ratcheting crimp tool for D sub contacts.
  • Length of 8.3inch (210mm)
  • Weight of 390g
  • Middle carbon steel and harden frame
  • SAE J404C alloy steel die
  • Black oxide finishing
  • Crimp open barrel connector size from 30AWG to 18AWG

Applications

Industrial
Back to top

Product Information


  • Crimp Tool Type
  • For Use With 30-18AWG D-Sub Contacts
  • Product Range -
  • SVHC To Be Advised

Availability

Availability:  45


  • 45 in stock for same day shipping
 
Check stock and lead times
    More stock available week commencing 8/15/16

Price for: Each

Minimum order quantity: 1

Order multiple quantity: 1

Price: $34.83 $34.83

Buy

Price

Quantity List Price
1 - 9 $34.83
10+ $31.34
 
 
Low

Legislation and Environmental


Back to top

Similar Products

Find products functionally similar to this one. Select one of the following links, and you will be taken to a product group page that presents all products in this category that share the given attribute.

Customer Reviews


MULTICOMP - HT-225D - RATCHET CRIMPING TOOL, D SUB CONTACTS 18-22 & 24-30 AWG 5 5 1 1
GREAT crimper for the money The standard header for the Arduino and RAMPS is the 2.54mm (.100") pitch header system. These are readily available as pins, and can be purchased for connectors with a little homework. I recently purchased sets of 4-pin and 3-pin crimpable pin connectors for use on the RAMPS V1.2. While having the proper connectors is good, not having a crimper that works effectively is bad. I have used needle nose pliers in a pinch, but B-style crimpers for these pins are the proper method to ensure an effective crimp that is unlikely to fail. I have a Sargent crimper I use for Tyco econoseal crimping in automotive connections for cars and motorcycles,as well as in my work doing automation controls, but it was too large for the significantly smaller 2.54mm header pins.It would leave the insulation crimps undone, and would only properly reverse the conductor tabs part of the time. The rest of the time it would bend it in the wrong direction, requiring more work with the needlenose. The worst part about this is that the opening in the header connector body doesn't have enough space to allow for much error in the crimped end dimensions, and I wasted at least 1 for every 5 with it either failing to due dimensional tolerances, or sdimply breaking off. If more than 1 pin was already in the body and, due to a jammed pin, required removal for a new body, it stood as much chance to come out as be damaged on removal. This would be bad. The solution? I did some research and found the proper sized crimper. I bought the MultiComp HT-225D. First off, it was only $26, which had me concerned, but on another electronics forum, the reviewer swore by it, so I figured since I have about $500 in the machine, $26 for a crimper was the least of my worries and worth checking out. It was delivered yesterday, and the difference in the quality by having the correct crimper is ASTOUNDING. I get a nice, clean crimp, all tabs bend correctly, fits right intot he connector body easily, and doesn't damage the wire body behind the crimp, which was causing failures. The insulation tab crimp is almost exactly the same size as the conductor tab crimp, nice and square, which lends itself to a clean insertion into the connecvtor body. Based on my satisfaction with the quality and affordability of the device, I may be looking into buying more to replace the Sargent that it seems FAR superior to. I will also be buying replacement jaws for the unit, because they do suffer from wear over time, and I'd be less then thrilled to find the unit was no longer offered when I needed new jaws. Bottom line: Well worth the $26 to have a proper crimp on connector pins. Highly recommended. September 1, 2011
  • 2015-06-11T15:21:37.471-05:00
  • bvseo_lps, prod_bvrr, vn_prr_5.6
  • cp-1, bvpage1
  • co_hasreviews, tv_1, tr_1
  • loc_en_US, sid_01P3570, prod, sort_default
1-1 of 1
Back to top

Customer Q&A Exchange

(There are 4 questions : 4 answers on this product)

Product Q&A

Ask your questions. Share your answers.

 
 
Browse Q&A
 
 
Search Questions
Need Product Support?
If you need immediate technical support use Live Support or Contact Us.
This space is yours...
Use this space to Ask your peers product questions or Answer those questions posted by them.
Sort by
3 years, 9 months ago
by
snuf
0points
0out of 0found this question helpful.
Was this helpful?(0)(0)

Answers

A: 
Yes, Newark part number 01P3570 can be used for molex mini-fit jr terminals ( 5556/5558).
3 years, 9 months ago
by
TechGTC
0points
0out of 0found this answer helpful.
Was this helpful?(0)(0)
Details: 
this is used with the 1.27 (0.050 pitch terminal.
If not then what tool can I use?
3 years, 6 months ago
by
bilpenner
0points
0out of 0found this question helpful.
Was this helpful?(0)(0)

Answers

A: 
Multicomp 1250TH terminal is not a valid part. Seems to be looking crimp tool for multicomp part 1250TM terminal, suggetsed crimp tool part is Newark code 63R5811.
3 years, 6 months ago
by
TechGTC
0points
0out of 0found this answer helpful.
Was this helpful?(0)(0)
4 months, 3 weeks ago
by
Lux Tech
0points
0out of 0found this question helpful.
Was this helpful?(0)(0)

Answers

A: 
This crimp tool HT-225D is for D-Sub & Open Barrel Connectors. So in this case female contacts(16-02-0096) should work with this crimp tool. But the supplier recommended crimp tool part is 63825-8800 (Newark code 29X6327 ).
4 months, 2 weeks ago
by
TechGTC
0points
0out of 0found this answer helpful.
Was this helpful?(0)(0)
4 months ago
by
bikemstr
 - Vancouver, WA
0points
0out of 0found this question helpful.
Was this helpful?(0)(0)

Answers

A: 
This tool can not be used to crimp Molex SPOX contacts.
3 months, 1 week ago
by
TechGTC
0points
0out of 0found this answer helpful.
Was this helpful?(0)(0)
1 of 1
  • 2015-06-11T15:21:07.229-05:00
  • bvseo_lps, prod_bvqa, vn_prr_5.6
  • cp-1, bvpage1
  • co_hasquestionsanswers
  • loc_en_US, sid_01P3570, prod, sort_default
1 of 1

Community

Like to see information about this product from other customers?

 Read discussions, blogs, documents from our community members.

Filters:

Post a question to one of our experts or start a discussion and get responses from supplier experts and fellow engineers in our community.

Substitutes


  Newark Part No. Manufacturer Part No Manufacturer / Description
Avail Price Qty
ascdsc ascdsc ascdsc ascdsc ascdsc
Suggested Substitutes
24R6761
LY8-060

LY8-060

MULTICOMP

CRIMP TOOL, BOOTLACE, CORD END

Availability:​ 1  

Price for: Each

1+ $46.16 25+ $44.24 50+ $42.31 100+ $40.39 More pricing

Buy

Freight Charge: $20.00 once per order

Delivery in 5-7 days for in stock items

More stock available week commencing 9/12/16

Associated Products


Customers Also Bought